1.8" Hard Drives - Confirmed to Work

W

webdude12

Joined
Jul 10, 2008
Messages
32
Reaction score
0
To save some of us alot of headaches, I am going to start a thread on 1.8" compatibility.

I have finally got my Flip Cables in, and the ZIF Hard drive I have does not work. Can you please post in the following format:

Manufacture - Model Number - Flip/Standard Cable

WORKING
MK300GAL
and therefore probably
MK600GAL
HTC426020G5CE00 - Flip Cable
Hitachi - C4K60 - Flip Cable (Please Note: If you try with the standard cable you will burn up your Hard Drive, I managed to Burn two (2) up before I figured this out. :evil:

NOT WORKING
 
Did you try using something like UBCD to format it?
Mine wasn't recognised by BIOS, but was by some utilities on UBCD, but none would format properly, and then it started clicking, so it was definitely broken..
Rory
 
I hadnt tried UBCD, but I just did and the drive is not seen, by any of the utilities. The drive spins up just fine, and even clicks when cut power. So its getting proper signal, its just not compatible with the controller. And since Acer doesnt allow us to manually set parameters, we are out of luck on this drive. :-/
 
toshiba 30 60gb are working smoothly mk300 or mk600 something . youl notice that when you insert the AAO original cable to the 1.8 HD it wont fit . dont loose hope just pass a sand paper or a nail file to thiner the cable it works perfect
 
and i just installed windows xp sp3 without using NLITE .no lag at all quick and smooth . before it was ahell of booting and i had to wait to long to open a program had to do the hd trick at the end it still slow but now its good so happy . im thinking now what if i install a windows lite mmm sounds yummy
 
torrentlord said:
toshiba 30 60gb are working smoothly mk300 or mk600 something . youl notice that when you insert the AAO original cable to the 1.8 HD it wont fit . dont loose hope just pass a sand paper or a nail file to thiner the cable it works perfect
Click to expand...
exact model number please?
Rory
 
torrentlord said:
i used a MK300GAL or MK600GAL works fine
Click to expand...
Are you certain these are the exact model numbers? I know of the MK3008GAL, but not MK300GAL. Is it a new product?
 
Not quite sure : MK3006GAL, MK3008GAL and MK3009GAL are all different models, for instance...
 
SbM said:
torrentlord said:
i used a MK300GAL or MK600GAL works fine
Click to expand...
Are you certain these are the exact model numbers? I know of the MK3008GAL, but not MK300GAL. Is it a new product?
Click to expand...

I think he ust means the MK300*GAL and MK600*GAL versions should work fine.


Although, this shouldn't be a place of guessing, the whole point is to report drives that do work.

Rory
 
Hitachi - C4K60 - Flip Cable (Please Note: If you try with the standard cable you will burn up your Hard Drive, I managed to Burn two (2) up before I figured this out. :evil:
 
I just purchase a C4k60 from ebay that was a working pull from a Zune MP3 player. Can I use the existing cable in the One and just flip it on the board side zif socket. Is there enough of the cord to fold so that everything fits neatly into the case?

I did a little searching for a "flip cable" but had no luck. Do you have a source and part number for the right cord?

thanks in advance.

James (from Pittsburgh)

webdude12 said:
Hitachi - C4K60 - Flip Cable (Please Note: If you try with the standard cable you will burn up your Hard Drive, I managed to Burn two (2) up before I figured this out. :evil:
Click to expand...
 
I have (7) Flip cables that I will mail to the US only for $3.00 each including postage. PM me for my paypal email address if you are interested. I am in TN, and will mail via US Mail to the United States only.
 
I ordered them off ebay from Hong Kong. I have 2 left. Anyone need one, PM me, and I will send you a Paypal shopping cart link. Please remember, I am sending these via US Mail, and will ship to the US only. :-)
 
Thanks! The cable you sent me did the trick. I've upgraded my AAO with a Hitachi 30GB 1.8" drive and it is outstanding. It is a dream compared to the SSD drive. I recommend this mod to anyone thinking of replacing the SSD. It cost me $36 total and took about an hour to install not counting the OS. This difference is night and day. No hangs at all with this setup.


webdude12 said:
I have (7) Flip cables that I will mail to the US only for $3.00 each including postage. PM me for my paypal email address if you are interested. I am in TN, and will mail via US Mail to the United States only.
Click to expand...
 
I can confirm that a TOSHIBA HDD 120GB 4200RPM 1.8# ATA-LIF MK1214GAH is working with no problems. The default cable from the SSD doesnt fit without trimming it down a bit, otherwise a really nice disk. You also have to mod the chassi a little to make it fit.
 
You must log in or register to reply here.

Latest threads

Back
Top